Home > Auto Lifts > Two Post Lifts >

Atlas ATTDPV10PX, PV-10P Overhead 10,000 lb. Capacity Adj Height 2-Post Lift

Atlas XH-PV10PX

Alternative Views:

Your Price: $3,799.00
Call us at 888-998-8665 for our current Atlas promotion.

Product Code: ATEXH-PV10PX

Unloading Equipment

I have the equipment to unload it.
Ship to local freight terminal for will call.
Ship to an installer for delivery & install.
Please call me for other options for delivery.

Qty:

Description

Specifications

Atlas XH-PV10PX

The commercial grade Atlas PV-10P two post lift includes some modifications and improvements that make it one of the most popular above ground lifts in the world.

The Atlas PV-10P is the perfect choice for use in either a large commercial service department or for the "pole barn" owner who wants the "biggest and baddest" lift in the county. The Atlas PV-10P is designed and engineered to safely lift (and work on) everything from a Smart Car ® to a one ton diesel dually.

The Atlas PV-10P (the "P" means "padded") incorporates a "padded" shut-off bar to protect the top of the vehicle from contacting the crossbar. The carriages are equipped with "padded" protective (thick rubber) covers to help prevent the vehicle's doors from damage if opened into the columns or carriages.

The truck adapter set has been augmented (12 pieces vs. 8 pieces) and the rubber lift pad has been reinforced to ensure a solid contact with the vehicle's lifting point.

Most truck shipments will be delivered by a commercial freight carrier operating a tractor/trailer rig. The semi trailer will be enclosed. Most commercial carriers have smaller straight trucks and some have small flatbed trucks, but the majority of freight companies will not use these smaller trucks for your delivery. Atlas cannot guarantee the type of truck that will be used for delivery. You should assume that your product will be delivered on a tractor/trailer rig that uses a 53 foot enclosed trailer. This is a VERY LONG rig. It is the truck driver's responsibility to make sure that your product is brought to the back of the delivery truck. It is the customer's responsibility to unload the product from the truck.

Hydraulic Cylinder Configurations:
Atlas uses a newly designed cylinder configuration for the Atlas PV-10P lift.

There are two popular hydraulic cylinder configurations used in two post electric/hydraulic above ground lifts:

The base plate two post above ground lift implements the chain-over-roller configuration. This is the only hydraulic cylinder system that is possible in the base plate lift. The base plate two post above ground is designed for "low ceilings". The direct drive hydraulic cylinder configuration cannot be used in the base plate lift because the hydraulic cylinder would extend above the 9' 3" column when the lift arms were raised to the maximum height.

The "overhead" two post above ground lift may incorporate either the direct drive hydraulic cylinder or the chain-over-roller hydraulic cylinder.

Versatility:
The PV-10P two post car lift is designed to offer that extra amount of lifting capacity to safely lift dual wheel pick up trucks or fully loaded ¾ ton or ½ ton pick up trucks. The Atlas PV-10P also offers an extremely low lift pad position on the versa-metric lift arm configuration. This low pad height will allow the operator to position the lift arms under most small cars (with low pick up points) and heavier pick up trucks.

The peg style truck adapters included with the Atlas PV-10P two post car lift are necessary to lift vehicles with running boards. The Atlas PV-10P peg style truck adapters (12 extensions) can be combined to raise the lift pads to reach the frame of most pick up trucks without damaging the running boards.

The Atlas PV-10P has symmetrical columns and includes a set of versa-metric arms. These arms can be configured into the symmetrical position to lift a full loaded pick up truck OR these arms can be configured to the asymmetric position to offer easier opening of the front door on some vehicles.

The Atlas PV-10P two post above ground lift has single point release, overhead above ground configuration, versa-metric arm configuration. The Atlas PV-10P car lift is powered by a 220 Volt (single phase) power unit.

Flow Restrictor:
Atlas is proud to announce that many of our two post and four post lifts manufactured in our off shore factory (after 08-01-07) have flow restrictor valves installed in the hydraulic system. Some lifts do not require a flow restrictor.

Electrical Requirement:
The electric motor for the power unit requires 220 Volt (single phase) 60 Hz. We recommend using at least a 10 gauge (grounded) wire from the electrical panel. The power unit has a short pigtail (no plug) that can be wired to either a quick disconnect box (mounted on the lift column) or to a male/female plug combination. A 30 amp breaker is recommended.

Electrical Requirement:
220 volt single (1) phase. A 30 amp breaker is recommended.

The electric motor for this power unit requires 220 Volt (single phase) 60 Hz. We recommend using at least a 10 gauge (grounded) wire from the electrical panel. The power unit has a short pigtail (no plug) that can be wired to either a quick disconnect box (mounted on the lift column) or to a male/female plug combination.

We recommend that the power unit to NOT BE HARDWIRED directly to the main supply power cord. There should be some type of "quick disconnect" in close proximity to the power unit.

The 220 volt (single phase) motor will run on a 208 volt to a 240 volt power supply. Rule of thumb is that a 220 volt motor will operate effectively within a 10% plus or minus range of the supplied voltage. Based upon that assumption, a 220 volt motor will operate within a range of about 200 volts to 242 volts.

The 220 volt electric motor that is used on the power unit may vary between 1.5 HP. - 3 HP. The horsepower rating of the motor will not influence the "lifting power" of the lift. The motor is used to pressure a hydraulic pump. The pressure level of the hydraulic pump is preset to provide the correct amount of hydraulic pressure for the lift to work properly.

Motor manufacturers recommend that you use (wire the lift) a 30 amp service for this power unit. Power unit manufacturers use motors from several different electrical motor manufacturers. The 30 amp electrical service will provide enough power for the motor to operate properly, and also protect the motor from damage.

Installation:
The Atlas PV-10P two post car hoist should be installed on a solid concrete floor. This PV-10P concrete floor should have a minimum of four (4) inches of concrete with 3000 PSI. The Atlas comes with the mounting hardware to anchor your two post lift to the appropriate concrete floor.

Most of our above ground lift customers install their own car lifts. The average time to install the Atlas PV-10P car lift is four hours.

We provide detailed installation instructions with all our two post above ground lifts and our four post above ground lifts.

Safety Labels:
In a concerted effort to improve customer awareness as to the correct operation of our two post and four post above ground lifts, the factory is affixing the ANSI (ALI/101S) safety labels to our Atlas and Direct above ground vehicle lifts (after 08-01-07). These ANSI (ALI/101S) safety labels help to alert the operator as to certain potential dangers that may exist in the normal operation of the lift.

Parts:
Atlas stocks a complete inventory of lift parts for all the lifts we sell. Lift parts and technical support personnel are available.

Certain competitors do not stock the lifts they advertise and do not stock any of the lift parts or accessories. Lifting a car is serious business.

Warranty:
(5) years on structural components and (2) year on hydraulic power units and cylinders from invoice date.

Features

Commercial Grade
Single Point Lock Release
Versa-Metric Arms
"Padded" Shut-off Bar
Thick rubber covers on carriages
Atlas Power Coat powder coat finish
Adjustable Height - 11'10" or 12'2"
Free 12 piece truck adapter set
Mounting Hardware Included
5 Year Structural Warranty, 2 Year Power Unit Warranty

Atlas XH-PV10PX

Atlas® XH-PV10PX Specifications
Capacity	10,000 LB.
Overall Height	143 1/8" (11’ 11 1/8”) or 146 7/8” (12’ 2 7/8”)
Overall Floor Width	137 1/2" (11’ 5 1/2”)
Outside Column to Outside Column	125 1/2" (10’ 5 1/2")
Maximum Lift Height (Without Adapters)	72 1/2"
Maximum Lift Height (With Adapters)	81 1/4"
Minimum Arm Height	4 1/2"
Inside Column	110 1/8” (9’ 2 1/8”)
Drive Thru	96 1/4” (8’ 1/4") Symmetric/ 90 1/4" (7' 6 1/4") Asymmetric
Column Size	7 1/2" x 14 1/2"
Column Thickness of Steel	6mm
Base Of Lift	17 1/2" x 20 1/2"
Motor/Electrical Requirement	220 volt single (1) phase. A 30 amp breaker is recommended
Oil Requirement	3-5 Gallons AW32/AW46 (NOT INCLUDED)
Shipping Weight	1,875 LBS.
Adapter Heights	4 Each 1.25”, 2.5”, 5”
Arm Hole/Adapter Peg Size	1.5”

Atlas® Two Post Overhead Comparison Chart
Attribute	9KOHX	9OHSC	OHX10X	PV10P	PV12P	PV15P
Capacity	9,000 LB .	9,000 LB .	10,000 LB .	10,000 LB .	12,000 LB .	15,000 LB .
Overall Height	138" (11’ 6") or 142” (11’ 10”)	142" (11’ 10")	152" (12’ 8”)	143 1/8" (11’ 11 1/8”) or 146 7/8” (12’ 2 7/8”)	165" (13’ 9”) or 177” (14’ 9”)	165" (13’ 9”) or 177” (14’ 9”)
Overall Floor Width	134 1/2" (11’ 2 1/2")	133 1/2" (11’ 1 1/2")	144 3/8" (12’ 3/8")	137 1/2" (11’ 5 1/2”)	150 3/8" (12’ 6 3/8”)	151 3/8" (12’ 7 3/8”)
Outside Column to Outside Column	124 7/8" (10’ 4 7/8")	125 1/2" (10’ 5 1/2")	136" (11’ 4")	125" (10’ 5")	139 1/8" (11’ 7 1/8")	139 1/8" (11’ 7 1/8")
Maximum Lift Height (Without Adapters)	74 1/2"	76 3/4"	74 3/4"	71 7/8"	72 1/8"	75 1/8"
Maximum Lift Height (With Adapters)	81"	87 3/4"	85 3/4"	82 7/8"	83 1/8"	86 1/8"
Minimum Arm Height	4"	4"	4 1/2"	4 3/8"	4 1/2"	7 1/4"
Inside Column	110” (9’ 2”)	109 1/2” (9’ 1 1/2”)	118 1/4” (9’ 10 1/4”)	110 3/8” (9’ 2 3/8”)	122 5/8” (10’ 2 5/8”)	123 1/2” (10’ 3 1/2”)
Drive Thru	100” (8’ 4”) Symmetric/ 90 1/2" (7’ 6 1/2”) Asymmetric	100 1/2” (8’ 4 1/2”)	106 7/8” (8’ 10 7/8”)	96” (8’)	108 5/8" (9’ 5/8”)	109 7/8" (9’ 1 7/8”)
Base Of Lift	14 1/4" x 18"	16 3/4" x 17 3/4"	18 1/2" x 21 1/2"	17 1/2" x 20 1/2"	17 1/2" x 20 1/2"	17 1/2" x 20 1/2"
Motor/Electrical Requirement		220 volt single (1) phase . A 30 amp breaker is recommended

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Auto Lifts > Two Post Lifts

Atlas ATTDPV10PX, PV-10P Overhead 10,000 lb. Capacity Adj Height 2-Post Lift

Atlas XH-PV10PX

Atlas XH-PV10PX

Atlas® Two Post Overhead Comparison Chart